News and Events

Precision Plano Optics: Specifying Flatness, Surface Quality and Parallelism

Written by Torrent Photonics | Nov 17, 2026

Windows, flats, beamsplitter plates, filter substrates and reticles are often among the simplest components in an optical assembly. They are also frequently over-specified.

Flatness, surface quality and parallelism all affect optical performance, but tighter tolerances do not automatically improve a system. Understanding which specifications matter for a particular application can reduce cost, shorten lead times and simplify manufacturing without compromising performance.

Flatness

Flatness is often one of the first specifications tightened on a drawing and one of the most commonly over-specified.

Most flatness specifications are stated in waves at a test wavelength, typically 632.8 nm. A λ/10 specification corresponds to a peak-to-valley surface deviation of approximately 63 nm.

The key question is not how flat a surface can be made, but whether tighter flatness provides a measurable benefit in the finished system.

For applications where the transmitted or reflected wavefront is critical, such as interferometry, metrology and high-performance imaging systems, flatness can have a direct impact on optical performance. In less demanding applications, tighter specifications may add cost without delivering a meaningful improvement.

Flatness is typically measured using a Fizeau interferometer against a reference flat. The specification normally applies across the clear aperture rather than the full component.

Part geometry also affects achievable flatness. Thin windows and substrates are more susceptible to distortion during polishing, coating and mounting. A component that meets specification before coating may not exhibit the same flatness once it is integrated into an assembly.

Surface quality

Surface quality is commonly specified using scratch-dig values such as 60-40, 40-20 or 10-5.

The scratch value is not a physical scratch width. It is a visibility classification determined by comparison to calibrated standards. Dig values refer to the maximum permitted pit size in hundredths of a millimeter.

Surface quality requirements should be driven by the function of the optic.

In laser systems, scratches and digs can increase scatter and act as initiation sites for laser damage. In imaging systems, defects close to an image plane are more likely to be visible than defects elsewhere within the optical path.

Some customers specify surface quality using MIL-PRF-13830, while others use ISO 10110-7. The two systems are not directly interchangeable, so the required standard should be identified at the start of a project.

Parallelism and wedge

Parallelism controls the angular relationship between the two faces of a plano optic.

A small wedge angle can introduce beam deviation, which may become significant in boresighted systems, rangefinders, optical instruments and precision alignment applications.

For N-BK7, a wedge of 1 arcminute produces approximately 31 arcseconds of beam deviation. While insignificant in some applications, the same error may be unacceptable in systems where optical alignment is critical.

Perfect parallelism is not always desirable. Parallel surfaces can create unwanted etalon effects, ghost reflections and interference fringes. For this reason, optical windows used in laser systems are often manufactured with a controlled wedge rather than maximum parallelism.

Typical specification levels

Typical specifications vary considerably by application.

Grade

Flatness (PV at 633 nm)

Surface Quality

 

Parallelism

Commercial

λ/2 to λ/4

80-50 to 60-40

 

~3 arcmin

Precision

λ/10

40-20

 

~30 arcsec

High precision / laser

λ/20 or better

20-10 to 10-5

 

<5 arcsec

 

Reticle substrates

Reticles place unique demands on plano optics because they are positioned at an image plane.

Any surface defect, contamination or substrate imperfection can appear directly in the viewed image, often immediately adjacent to the reticle pattern itself. A scratch that would be insignificant on a protective window can become highly visible in a sighting system.

Substrate quality is particularly important before an etch-and-fill reticle pattern is applied. Cosmetic defects, contamination and substrate wedge can all affect final performance.

The same considerations often apply to windows and beamsplitter plates used in rangefinders and night vision systems, especially where components are positioned close to an image plane.

Matching the specification to the application

Reducing flatness from λ/10 to λ/20, tightening surface quality from 40-20 to 10-5, or moving from arcminute to arcsecond parallelism all increase manufacturing complexity and inspection requirements.

The most effective approach is to determine which surfaces influence wavefront quality, image quality or alignment accuracy, and apply tighter specifications only where they provide a measurable benefit.

Discussing these requirements before a drawing is released often leads to a more manufacturable design and a more cost-effective solution.

Discuss your application with our team

Torrent Photonics manufactures precision plano optics, windows, reticle substrates and optical assemblies for aerospace, defence, optical metrology and imaging applications.

To discuss a drawing or review a specification, contact our team: https://torrentphotonics.com/contact-us